In amplitude modulation
(AM), the amplitude of a carrier wave whose frequency remains constant changes
in response to the modulating signal. In frequency modulation (FM), it is the
frequency of the carrier that varies with the amplitude of the modulating signal.
The carrier frequency deviates more when the modulating signal amplitude is
higher. There are two important consequences. Because noise is characterized by
large amplitude variations, it impacts AM transmission to a greater degree than
FM transmission, giving FM a higher signal-to-noise ratio. FM transmission,
however, requires greater bandwidth, which in today’s crowded FM spectrum, may
be seen as a liability.
HDMI Encoder Modulator,16in1
Digital Headend, HD RF Modulator at Soukacatv.com
AM and FM are two
widely-used analog modulation methods. Others are phase modulation (PM),
quadrature amplitude modulation (QAM), space modulation (SM) and
single-sideband modulation (SSBM).
Phase modulation, like
frequency modulation, is a form of angle modulation. In FM the frequency of the
carrier varies to signify changes in amplitude of the modulating signal. In PM
it is the phase of the carrier wave that is varied. Here again, frequency and
amplitude of the carrier remain constant.
The phase of a propagated
wave with respect to another propagated wave refers to the relative difference
in their instantaneous values in time, as represented by positions on the
X-axis of an oscilloscope display when the instrument is operating in the time
domain. If successive waveforms are time-shifted in that way, information can
be conveyed.
Common applications for phase modulation are
Wi-Fi, the Global System for Mobile Communications (GSM), satellite television,
signal and waveform generation in digital synthesizers, and phase distortion in
sound synthesizers.
Quadrature amplitude
modulation appears as a scheme for information encoding in both analog and
digital modulation. In both modes, two analog signals or two digital bit
streams are conveyed by modulating the amplitudes of two simultaneous carrier
waves. In the digital domain, amplitude-shift keying is used while in the
analog domain it is amplitude modulation that is operative.
SKD3013 3 Channel HD Encode Modulator
SKD19 Series 1U Rack 12CH Encode Modulator
The two carrier waves,
which are of the same frequency, are in a quadrature relationship, or
orthogonality, which is to say that they are 90° out of phase. Accordingly,
they can be demodulated. QAM is used for Wi-Fi and for optical fiber signal
transmission. The sender and receiver must have accurate clock signals in
common. If they do not maintain synchronicity, the signals lose resolution and
are subject to crosstalk. To avoid this corruption, a burst subcarrier is
typically included. An example, in NTSC TV transmission, is the color burst.
Space Modulation (SM) differs from the types
discussed above in that its purpose is not to facilitate transmission between
transmitters and receivers, but rather to aid aircraft in modeling surrounding
spaces to help land safely. Demodulation takes place in the space between an
aircraft and its intended touchdown location rather than within the
instrumentation. Multiple antennas fed with diverse signals create discrete
depths of modulation, from which is derived the required positional
information.
In SM, carriers at 110 MHz and 330 MHz are
modulated by 90 Hz and 150 Hz tones. These signals are conveyed from runway to
aircraft to facilitate accurate landing.
Single-sideband (SSB)
modulation, also known as single-sideband suppressed-carrier (SSB-SC)
modulation, has been used since the first decades of radio transmission to
convey information using reduced power and bandwidth. Conventional amplitude
modulation concerns itself with an output signal that is twice the bandwidth of
the modulating signal. Accordingly, one-half of an AM transmission is
eliminated in SSB modulation by suitable filtering with no loss of information;
dual sidebands are essentially redundant. The downside and reason SSB is not
used universally is the more complicated circuitry at the transmitter and
tuning problems at the receiver.
Despite its greater
efficiency and lower bandwidth requirements, SSB is not used for broadcasting.
Frequency stability and selectivity are beyond the capability of inexpensive
receivers. But SSB is justified in point-to-point communication where more
advanced receivers are the norm and can be modified as needed.
SSB was first patented in 1915 and used
successfully in a 1920s radio-telephone link between New York and London.
Telephone companies in the 1930s used SSB over long-distance lines in
conjunction with frequency-division multiplexing (FDM).
FDM is a basic form of multiplexing which, as
the name implies, consists of conveying two or more signals simultaneously
through a link. In its simplest form FDM frequencies have non-overlapping
bandwidths, so they can be selected at the receiver using ordinary filtering
techniques.
Multiplexing is a generic term meaning that
multiple signals are sent through a single conductor without mutual
interference. SSB lends itself to FDM because one sideband is not part of the
transmission, so the modulated carrier occupies only one-half the conventional
FM bandwidth. So twice as many multiplexed signal can be transmitted.
Frequency modulation
is also used to convey digitized data. This is done by shifting the carrier
frequency among various frequencies that represent digits. In a typical
implementation, one specified frequency represents 0 and another represents 1.
This is frequency-shift keying (FSK) and it is used in fax and other modems,
for Morse Code and in radioteletype. Other varieties of modulation adapted for
digital communication are ASK, APSK, CPM, MFSK, MSK, OOK, PPM, PSK, SC-FDE, TCM
and WDM:
·
Amplitude-shift keying (ASK) is a
variety of AM that varies the amplitude of a carrier wave to denote 0 or 1.
·
Asymmetric phase-shift keying (APSK)
conveys digital information by modulating amplitude and phase of the carrier.
·
Continuous phase modulation (CPm0)
is used in wireless modems. Rather than the carrier phase resetting to zero at
the start of each symbol, the carrier phase is modulated continuously. CPM is
characterized by high spectral and power efficiency.
·
Multiple frequency-shift-keying
(MFSK) resembles FSK, but more than two frequencies are used.
·
Minimum-shift keying (MSK) rather
than using square pulses, consists of half sinusoids to encode each bit.
·
On-off keying (OOK) denotes digital
voltage levels, i.e. zeros and ones, by the presence or absence of the carrier
wave.
·
Pulse-position modulation (PPM)
denotes digital bits by transmitting single pulses in shifting positions.
·
Phase-shift keying (PSK) denotes
digital bits by modulating the phase of the carrier wave. It is used for LANs,
RFID and Bluetooth protocols.
·
Single-carrier FDMA is a
frequency-division multiple access format. It assigns multiple users to a
single communications channel.
·
Trellis coded modulation (TCM)
efficiently transmits information over narrow-band telephone lines.
·
Wavelet digital modulation (WDM)
uses wavelet transformations to denote digital values.
Pulse-width
modulation is used primarily to control industrial machinery including the
speed and torque of three-phase induction motors by means of variable frequency
drives (VFD).
Prior to the
introduction of VFD in the 1960s, the speed of an ac motor could not be
controlled practically. Reducing the voltage supplied to the motor would slow
it down, but this transformed it into a less powerful motor, slowed only
because it was now overloaded. The unfortunate result was immediate heating of
the motor windings. For this reason, the ac motor was unsuitable for many
applications, such as for elevators and ski lifts, where smooth speed control
is essential.
The VFD functions by
feeding into the motor windings, not the traditional sine wave as supplied by
the utility, but a square wave, whose duty cycle can be varied. The traditional
square wave has a 50% duty cycle, which means half the time the voltage is high
(on) and half the time it is low (off), with fast transitions. The VFD, in
response to a low-voltage control signal, can vary the duty cycle. Lowering the
duty cycle, meaning the power is off a greater portion of the time, slows the
motor because it reduces the average voltage. Under these conditions, however,
the motor never overheats because it is not actually powered by a lower
voltage.
Similarly, the duty
cycle can be raised above 50%, and the motor will run at higher-than-rated
speed with no adverse effects provided the bearings and cooling system are okay
with the increased RPM.
Established in 2000, the Soukacatv.com main
products are modulators both in analog and digital ones, amplifier and
combiner. We are the very first one in manufacturing the headend system in
China. Our 16 in 1 and 24 in 1 now are the most popular products all over the
world.
For more, please access to
https://www.soukacatv.com.
CONTACT US
Company: Dingshengwei Electronics Co., Ltd
Address: Bldg A, the first industry park of
Guanlong, Xili Town, Nanshan, Shenzhen, Guangdong, China
Tel: +86 0755 26909863
Fax: +86 0755 26984949
Mobile: 13410066011
Email: ken@soukacatv.com
Source: testandmeasurementtips
没有评论:
发表评论